专业各种,DC插座,DC电源插座,DC插口,DC接口,DC母座,,DC电源插头,DC插头,欢迎订购.
DC电源插座主要适用于各种电子产品。例如：玩具，手机，笔记本电脑，数码产品，医疗设备，仪器仪表等。
DC电源插座SMT中心针有:0.5mm/0.7mm/1.0mm/1.1mm/1.3mm/1.65mm/2.0mm/2.5mm/3.0mm
DC插座型号有：DC-001，DC-003，DC-001A，DC-003A，DC-002，DC-004，DC-002A，DC-005，DC-002C，DC-005A，DC-005B，DC-009，DC-005C，DC-009ADC-006，DC-009C，DC-006A，DC-010，DC--006B,DC-011,DC-007,DC-011A,DC-011B,DC-013A,DC-012,DC-014A,DC-012A,DC-015,DC-012B,DC-015,DC-012B,DC-015A,DC-013,DC-015B,DC-015C,DC-020,DC-016,DC-021,DC-016A,DC-022,DC-017,DC-023,DC-018,DC-023A,DC-019,DC-023B,DC-024,DC-027,DC-025,DC-028,DC-025M,DC-028A,DC-025BM,DC-029,DC-026,DC-030,DC-026M,DC-030A,DC-031,DC-038,DC-031A,DC-038A,DC-033,DC-039A,DC-035-1,DC-040,DC-036,DC-041,DC-043,DC-048,DC-044,DC-049,DC-045,DC-049A,DC-046,DC-050,DC-074,DC-051,DC-047,DC-052,DC-053,DC-066,DC-055,DC-068,DC-056,DC-070,DC-060,DC-096手机专用尾插。
1.0构造Tectonic
A型状、尺寸依照制品图而规定.
Shape, size in accordance with the provisions of map products.
B外观:各部位应良好无秤锈、裂痕、电镀不良现象.
Appearance : the good parts should weigh no rust, cracks, electroplating ill.
2.0 使用环境条件The use of environmental conditions
A环境湿度Humidity: 25℃~+70℃
B 相对湿度Relative humidity: ≤93% (+40℃)
C 机械性能Mechanical properties
D 动作力Power moves:3~25N
E 端子强度Terminal Strength
各端子在各方面承受500克力作用下,在10秒内,无脱落、破损等不良现象,但弯曲也可.
The terminals in all aspects under 500 Caledon role, in 10 seconds, without any loss, damage and other negative phenomena, but also bending.
4.0 电气性能Electrical Performance
A 额定电流Current ratings:DC 12V 1A.
B 接触电阻Contact resistance:50mΩ以下.
C 绝缘电阻Insulation Resistance:
在端子之间各端子与壳之间加AC 500V 条件下,持续1分钟测试.100mΩ以上. The terminal between the terminal and Shell in between 500V AC conditions, sustained a minute test Ω m above .100.
D 抵抗电压Resistance voltage:
在端子之间端子与壳之间加 AC 500V 60Hz 条件下,持续1分钟测量.无击穿现象出现. In between the terminal and the terminal shell in between AC 500V 60Hz conditions, sustained a minute measurement. No breakdown phenomenon.
5.0可靠性试验Reliability Test
A 寿命试验Life Test
以涂有薄层润滑脂的插头(涂润滑脂防止摩擦过热)以每分钟15~20次,无负载插座拨出5,000次，符合规格3.0和4.0规定值. Coated with a thin layer of grease plugs (TU Grease prevent friction overheated) per minute to 15 ~ 20, a no-load socket allocated 5,000, with the specifications 3.0 and 4.0 provides value
B 温度试验Temperature Test
将插座放置于40±2℃,相对温度90%~95%环境中,96个小时后取出,取去水滴,将插座放置于常温常湿环境中,于30分钟内测试,符合规格3.0和4.0要求. Socket to be placed on the 40 ± 2℃, relative humidity of 90% ~ 95% of the environment, 96 hours after the removal, taking a drop of water, will be placed in the socket temperature often wet environment, in the test within 30 minutes, with 3.0 and 4.0 specifications required.